Generic Hero BannerGeneric Hero Banner
Latest market news

Indian steel export revival hinges on demand rebound

  • Market: Coking coal, Metals
  • 19/11/22

The Indian government's move to remove export duties on steel may allow mills to raise capacity utilisation, although an export resurgence and the trajectory of prices will hinge on a demand rebound.

The finance ministry withdrew a 15pc export duty levied in late May on pig iron and steel products classified under HS codes 7201, 7208, 7209,7210,7213, 7214, 7219, 7222 and 7227 late on 18 November.

"The current measures will provide a fillip to the domestic steel industry and boost exports," the ministry said on 19 November.

The duties had pushed down India's finished steel exports in October to a more than three-year low of 360,000t, which was also lower by 66pc on the year. April-October exports were lower by 55pc on the year to 3.96mn t, according to data from the Indian steel ministry's joint plant committee. India had also turned a net importer of steel for the second time in four months in October.

"The fundamentals in India are much better so we would definitely like to focus on the domestic market but, at the same time, the excess capacity that is available and underutilised will help us be more cost effective and keep us in a position to cater to any international demand that may come," a senior official at a major domestic steelmaker said.

"Overall sentiments will improve, and global markets will once again start looking towards India," the official added.

International market situation

Weaker international markets and the export duties had prompted Indian steel mills to bring forward maintenance works to balance supply-demand fundamentals in past months. Domestic hot-rolled coil prices had hit a one-year low in early September because of a seasonally weak monsoon season and import arrivals.

International steel markets have been on a downtrend owing to high inflation, a looming recession and low domestic demand, but India has proved to be a bright spot as demand and prices in the country have not slumped significantly.

Indian steel exports had declined even before the duties were put in place, so "real exports" will happen when the global demand situation changes and until then shipments will be subdued, a major domestic steel exporter said. "But at least the shackles are not there anymore."

"Countries like Japan and Korea have withdrawn their cheap export offers in the recent days, helping push offers up by some $30-$40/t, so workability should start returning to the market," the exporter said.

"International market prices remain between poor and poorer, so the only apparent benefit right now will be slightly improved demand," the head of steel exports at a domestic producer said. "Hopefully we will see a much-improved January-March quarter, as this quarter is of little use now because it's too late to book orders for December arrival at Europe."

Market participants do not see an immediate price hike in the domestic market, but long product prices in the secondary market have picked up by 2,000-3,000 rupees/t ($24-37/t) across the country since the morning of 19 November, according to traders. There has been no price change for hot-rolled coil (HRC) so far.

Coking coal cost pressure continues

The finance ministry has also brought back an import duty of 2.5pc on anthracite/pulverised coal injection, coking coal and ferro-nickel and of 5pc for coke and semi coke, which were removed in May.

Record-breaking coking coal costs this year had pushed steel prices to an all-time high in April, forcing the Indian steel industry to call on the government to look at the volatility in metallurgical coal prices.

"Majority of the steel producers in India are coal dependent and putting that [import duty] will further add to the cost pressures, and those price levels continue to prevail at a significantly higher level," the senior company official at a major steelmaker said. "So that challenge continues to remain."

Iron ore

The government also removed its export tax on iron ore lumps and fines below 58pc Fe and iron ore pellets from the 50pc and 45pc duties imposed earlier. Iron ore lumps and fines above 58pc Fe will continue to attract a 30pc duty as was the case prior to the May duty announcements.

"It's a very welcome development. Exports help the iron ore industry, especially for low grades that are not utilised in country's steelmaking," Federation of Indian Mineral Industries secretary-general RK Sharma said. But it will take a while to revive the market at a time of oversupply in the global iron ore market and a weak Chinese economy, he added.

India's export, import duty changes on steel, raw materials
Product nameHS codePrevious dutyNew duty
Iron ores and concentrates260150pc (for all categories)30pc (for above 58pc Fe), 0 for other grades
Iron ore pellets2601 (26011210)45pc0
Pig iron and spiegeleisen in pigs, blocks or other primary forms720115pc0
Flat-rolled products of iron or non-alloy steel, of a width of 600mm or more, hot-rolled, not clad, plated or coated720815pc0
Flat-rolled products of iron or non-alloy steel, of a width of 600mm or more, cold-rolled (cold-reduced), not clad, plated or coated720915pc0
Flat-rolled products of iron or non-alloy steel, of a width of 600mm or more, clad, plated or coated721015pc0
Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel721315pc0
Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn721415pc0
Flat-rolled products of stainless steel of width >=600mm721915pc0
Other bars and rods of stainless steel; angles, shapes and sections of stainless steel722215pc0
Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel722715pc0
Anthracite/pulverised coal injection (PCI)2701 (27011100/27012010)02.5pc
Coking coal2701 (27011910)02.5pc
Coke and semi-coke2704 (270400)05pc
Ferro-nickel7202 (720260)02.5pc
Note: Duties mentioned for iron ore and steel products are for exports, while anthracite/PCI, coking coal, coke and ferro-nickel are for imports

Sharelinkedin-sharetwitter-sharefacebook-shareemail-share

Related news posts

Argus illuminates the markets by putting a lens on the areas that matter most to you. The market news and commentary we publish reveals vital insights that enable you to make stronger, well-informed decisions. Explore a selection of news stories related to this one.

News
04/04/25

Egyptian rebar clears EU customs as merchant bar

Egyptian rebar clears EU customs as merchant bar

London, 4 April (Argus) — Egyptian rebar has cleared at the Lithuanian port of Klaipeda under a product code that sits under a different EU quota category, a mill test certificate sent to rebar buyers and obtained by Argus shows. The documentation shows a parcel of steel products with the properties and specifications of rebar registered under HS code 722830, which is for hot-rolled bar, not rebar. The material is supplied by an Egyptian steel mill, and the mill test certificate obtained by Argus contains the assertion "HS code for rebar is: 72 28 30 69 00", followed by the signature of a senior quality engineer. The mill's website indicates it produces rebar, rebar in spools and rebar in coil, which fall respectively under the rebar and wire rod EU import quotas. Hot-rolled bar under the HS code 72283069 falls under category 12 for "non-alloy and other alloy merchant bars and light sections", for which there is currently no import restriction on Egyptian material. A trading company is thought to have discharged at least 17,000t of rebar and rebar in coils at Klaipeda on 28 March, after loading at the Egyptian port of Alexandria on 24 February. But it is not clear how much material in total has passed through customs or under which HS codes. As of 1 April, the EU's Egyptian rebar quota is capped at about 27,500t, after previously having had no limitation within the "other countries" allocation of about 138,000t. Some market participants estimated that there were about 80,000t of Egyptian rebar waiting to clear at EU ports on 1 April, but only about 30,000t cleared under the rebar quota on the first day, according to market participants, meaning duties paid by companies clearing material on that day will not be as high as feared. Trade data also show that Bulgaria imported 17,000t of hot-rolled bar from Egypt under HS 72283069 in January 2025, nearly three times as much as the whole EU imported in the full year of 2024 or 2023, a sign that companies are increasingly keen to seek ways around EU safeguards as they tighten. By Brendan Kjellberg-Motton Send comments and request more information at feedback@argusmedia.com Copyright © 2025. Argus Media group . All rights reserved.

Find out more
News

Tariffs and their impact larger than expected: Powell


04/04/25
News
04/04/25

Tariffs and their impact larger than expected: Powell

New York, 4 April (Argus) — Federal Reserve chairman Jerome Powell said today tariff increases unveiled by US president Donald Trump will be "significantly larger" than expected, as will the expected economic fallout. "The same is likely to be true of the economic effects, which will include higher inflation and slower growth," Powell said today at the Society for Advancing Business Editing and Writing's annual conference in Arlington, Virginia. The central bank will continue to carefully monitor incoming data to assess the outlook and the balance of risks, he said. "We're well positioned to wait for greater clarity before considering any adjustments to our policy stance," Powell added. "It is too soon to say what will be the appropriate path for monetary policy." As of 1pm ET today, Fed funds futures markets are pricing in 29pc odds of a quarter point cut by the Federal Reserve at its next meeting in May and 99pc odds of at least a quarter point rate cut in June. Earlier in the day the June odds were at 100pc. The Fed chairman spoke after trillions of dollars in value were wiped off stock markets around the world and crude prices plummeted following Trump's rollout of across-the-board tariffs earlier in the week. Just before his appearance, Trump pressed Powell in a post on his social media platform to "STOP PLAYING POLITICS!" and cut interest rates without delay. A closely-watched government report showed the US added a greater-than-expected 228,000 jobs in March , showing hiring was picking up last month. By Stephen Cunningham Send comments and request more information at feedback@argusmedia.com Copyright © 2025. Argus Media group . All rights reserved.

News

Silicon, ferro-silicon hit by US tariffs


04/04/25
News
04/04/25

Silicon, ferro-silicon hit by US tariffs

London, 4 April (Argus) — Silicon and ferro-silicon prices in the US are likely to surge because of steep tariffs on imports announced this week, while prices in Europe might fall as countries hit by high tariffs redirect material to the EU. The tariffs announced by President Donald Trump on 2 April exempted a number of minor metals and ferro-alloys, listed in Annex II of the executive order, but ferro-silicon and silicon metal of less than 99.99pc purity were not among the exemptions. The US steel industry is a major consumer of imported silicon products. The tariffs are the second major US trade announcement on ferro-silicon in two weeks after the International Trade Administration (ITA) determined anti-dumping duty rates against ferro-silicon imports from Brazil, Malaysia and Kazakhstan on 25 March. A final decision on anti-dumping duties is due on 12 May, and it remains to be seen how the new tariffs will impact the ITA's decision. Several major silicon and ferro-silicon producing countries are now subject to Trump's adjusted reciprocal tariffs, above the 10pc applied to all imports. Vietnam now has one of the highest tariff burdens at 46pc, Kazakhstan is subject to 27pc and Malaysia to 24pc. The countries have been major suppliers of silicon products to the US. In 2024, the US imported 27,084t of ferro-silicon from Malaysia, 13,119t from Vietnam and 10,262t from Kazakhstan. Silicon and ferro-silicon producer Ferroglobe, which has operations in the US, Canada and Europe, and which petitioned for the anti-dumping duties before the ITA, says it is too early to predict the full impact of the tariffs. "As a vertically integrated local producer in both the US and the EU, we believe that Ferroglobe will benefit from a more level playing field in both markets," the producer said. But sellers of heavily-tariffed material have taken immediate steps to reduce their exposure. "I just cancelled a lot of vessels from Vietnam because you cannot pay a 46pc tariff," a trader said on Thursday. Countries with lower tariffs stand to benefit if prices surge. A producer in one such country told Argus he expects his company's margins and market share in the US to increase. Brazil is subject to only a 10pc tariff, making Brazilian producers now among the most affordable for the US market. The US imported 59,971t of silicon metal and 33,182t of ferro-silicon from Brazil in 2024, comprising 40pc and 21pc of total silicon and ferro-silicon imports, respectively. Iceland is also subject to the base 10pc tariff, although for silicon metal there is a pre-existing anti-dumping duty on PCC BakkiSilicon at 47.54pc, and 37.83pc on all other sales from Iceland. Norway's tariff was set at 16pc, making it more competitive than the EU, which is subject to 20pc. The US imported 9pc of its silicon metal from Norway in 2024. Norwegian silicon and ferro-silicon producer Elkem, which exports silicon-based products to the US from Canada, Paraguay, Iceland and Norway, told Argus the company will be increasing prices on all products going to the US. "Given that the US is a net importer of our products, we expect prices in the US to increase by more than the raised tariffs on Elkem's products," the company said. US exports might be redirected to EU The European ferro-silicon market has been rattled by concerns of dumping in Europe. Many expect more affordable material from Kazakhstan, Vietnam and Malaysia to flood the European market because of trade diversions from the US. A European producer expects large quantities of ferro-silicon to flood the market. "I am very afraid that Kazakhstan especially can ship material to Europe and will take the risk," he said. The EU has said it will take steps to prevent dumping of cheap goods in Europe. But with the European steel industry under pressure from the tariffs, the EU might hesitate to take measures that could increase costs for the steel sector. EU safeguard investigation could face delays The European ferro-silicon and silicon industries have already struggled to compete with affordable imports from third-country competitors with lower production costs. On 19 December, the European Commission announced a safeguard investigation on imports of silicon, ferro-silicon and manganese alloys. Many market participants expected a decision on trade protection measures in April. Some traders have held on to stock in the hope of prices increasing after the announcement. But now producers, traders and consumers told Argus this week that they expect any decision on safeguarding the ferro-alloy industry to be delayed until tariff negotiations have been concluded. Some planned meetings on the measures have been cancelled, the producer heard, as priorities have shifted. A trader with stocks in Europe told Argus that if he hears confirmation that the safeguard announcement will be delayed, he and other traders will look to sell material. "Prices are only inflamed because of the safeguarding," the trader said. "If it's a six-month delay, prices might stay firm, but if it's a year, we can't wait." By Maeve Flaherty Additional reporting from Samuel Wood Send comments and request more information at feedback@argusmedia.com Copyright © 2025. Argus Media group . All rights reserved.

News

US adds 228,000 jobs in March: BLS


04/04/25
News
04/04/25

US adds 228,000 jobs in March: BLS

Houston, 4 April (Argus) — The US added a more-than-expected 228,000 jobs in March, showing hiring was picking up last month just as the new US administration began mass federal firings and announced tariffs on trading partners. Economists surveyed by Trading Economics had forecast job gains of 135,000 for March. The unemployment rate ticked up to 4.2pc in March from 4.1pc the prior month, the Bureau of Labor Statistics (BLS) reported today. Job gains in February were revised lower by 34,000 to 117,000 jobs. The unexpectedly strong job report comes amid mounting recession fears on the back of President Donald Trump's volley of trade tariffs unveiled this week and mass federal layoffs begun over the past month, which have yet to appear in the Labor surveys. US and global stocks have tumbled on the tariff news. As of 11am ET today, Fed funds futures markets are pricing in 43pc odds of a quarter point cut by the Federal Reserve at its next meeting in May and 100pc odds of at least a quarter point rate cut in June. Job gains averaged 159,000 over the 12 months prior to March. Federal government employment declined by 4,000 jobs in March following losses of 11,000 jobs in February. Employees on paid leave or receiving severance pay are counted as employed, the BLS said, so most of last month's announced federal job cuts do not show up in the data. Some federal job cuts have been reversed by court orders. Retail trade added 24,000 jobs, while transportation and warehousing added 23,000 jobs. Construction added 13,000 jobs and manufacturing added 1,000 jobs. Leisure and hospitality jobs grew by 43,000 and health care and social assistance added 78,000 jobs. Average hourly earnings rose by an annual 3.8pc, slowing from 4pc the prior month. By Bob Willis Send comments and request more information at feedback@argusmedia.com Copyright © 2025. Argus Media group . All rights reserved.

News

Funding cuts could delay US river lock renovations


03/04/25
News
03/04/25

Funding cuts could delay US river lock renovations

Houston, 3 April (Argus) — The US Army Corps of Engineers (Corps) will have to choose between various lock reconstruction and waterway projects for its annual construction plan after its funding was cut earlier this year. Last year Congress allowed the Corps to use $800mn from unspent infrastructure funds for other waterways projects. But when Congress passed a continuing resolutions for this year's budget they effectively removed that $800mn from what was a $2.6bn annual budget for lock reconstruction and waterways projects. This means a construction plan that must be sent to Congress by 14 May can only include $1.8bn in spending. No specific projects were allocated funding by Congress, allowing the Corps the final say on what projects it pursues under the new budget. River industry trade group Waterways Council said its top priority is for the Corps to provide a combined $205mn for work at the Montgomery lock in Pennsylvania on the Ohio River and Chickamauga lock in Tennesee on the Tennessee River since they are the nearest to completion and could become more expensive if further delayed. There are seven active navigation construction projects expected to take precedent, including the following: the Chickamauga and Kentucky Locks on the Tennessee River; Locks 2-4 on the Monongahela River; the Three Rivers project on the Arkansas River; the LaGrange Lock and Lock 25 on the Illinois River; and the Montgomery Lock on the Ohio River. There are three other locks in Texas, Pennsylvania and Illinois that are in the active design phase (see map) . By Meghan Yoyotte Corps active construction projects 2025 Send comments and request more information at feedback@argusmedia.com Copyright © 2025. Argus Media group . All rights reserved.

Generic Hero Banner

Business intelligence reports

Get concise, trustworthy and unbiased analysis of the latest trends and developments in oil and energy markets. These reports are specially created for decision makers who don’t have time to track markets day-by-day, minute-by-minute.

Learn more